
Article number: K1055VW1
WELDING
EQUIPMENT + PLASMA CUTTER New York 2500 SET
The New York 2500
from Vector Welding is a combined device for welding and plasma
cutting. With the adjustable AC/DC (AC/DC) mode, it
can be used for all weldable metals, includingAluminium.
With 10-200A in TIG mode, 10-170A in MMA/electrode mode and plasma cutting with 10-50A the device is well suited for installation, repair, maintenance and DIY.
Die New York 2500
offers everything you need for metal welding or cutting work.
This article is a complete
set consisting of a welding device with plasma cutter,
welding helmet, foot pedal, tungsten electrodes, 3kg welding rods, as
well as a comprehensive TIG and plasma accessory set.
NEW
YORK 2500 PROPERTIES & ADVANTAGES:
3in1 Combi-device: AC/DC TIG, MMA/STICK, Plasma cutting
AC/DC TIG welding: Processing of all weldable metals, including aluminum
The adjustable AC output frequency allows the operator to focus the arc and thus minimize the heat-affected zone.
The advanced AC balance control helps to maintain a pointed tungsten needle to keep the arc in the welding zoneWelding joint precisely.
pulse function: in pulse welding, the welding current alternates between output and peak current at the desired frequency. The longer the intervals, the less energy and heat is supplied to the workpiece
HF ignition (TIG/CUT)
2 cycles/4 cycles
MMA/STICK/E-HAND: coated electrodes are used - in this process, the electrodes are the arc carrier and filler metal in one.
hotstart: every NRestarting the welding generator provides overcurrent and thus helps to ignite the arc.
arc-force: Melted material passes more easily to the workpiece. Prevents the arc from going out if this material causes contact between the electrode and the molten pool.
anti-stick: automatically switches off the welding generator if the electrode sticks to the workpiece and has to be detached by hand without damaging the electrode clamp.
plasma cutter: CUT function using a plasma beam generated by electricity. ThisThis melts the material and removes it with compressed air - a precise cut is produced. With this process all conductive metals can be cut (e.g. steel, stainless steel, aluminium, copper, etc.)
cutting thickness: maximum 12mm (hand-guided), quality cut 8mm (hand-guided)
modern IGBT (Insulated Gate Bipolar Transistor) enables fast and therefore low-loss switching of electrical currents
job memory: the New York 2500 has 9 memory locations
NEW
YORK 2500 FEATURES:
NEW
YORK 2500 TECHNICAL DETAILS:
setting range welding current (TIG
mode) | 10 -200 A |
setting range welding current
(MMA/STICK mode) | setting range welding current
(MMA/STICK mode) |
setting range welding current (CUT
mode) | 20 - 50 A |
duration of operation (ED) TIG
40°C | 200 A at 18 V 40% |
duration of operation (ED)
MMA/STICK 40°C | 170 A at 26.8 V 25% |
Switch-on time (ED) Plasma cutter
40°C | 50 A at 100 V 40% |
Mains voltage | 1 x 230 Volt |
Mains frequency | 50 - 60 Hz |
Protection class | IP23 |
Dimensions in mm (L x W x H) | 380 x 160 x 360 |
Weight in kg | 11.5 |
Standards | EN60974-1 / EC60974-1 |
Maximum cutting capacity
(hand-guided) | 13 mm |
Quality cutting capacity
(hand-guided) | 8 mm |
NEW
YORK 2500 CONTROL SYSTEM:

1. display screen | 5. on/off | 9. selection key |
2. PULSE function | 6. superheat display | 10. hotstart/Arc Force/Anti Stick |
3. 2 bar/4 bar | 7. JOB and STORE | 11. parameter settings |
4. mode (MMA/WIG/CUT) | 8. AC/DC mode |
|

1. gas flow | 5. secondary flow | 9. final flow |
2. start flow | 6. pulsePulse width (%) | 10. gas lag |
3. current rise | 7. pulse frequency (Hz) | 11. AC frequency |
4. welding current (primary) | 8. current reduction | 12. AC balance |
NEW YORK 2500 TECHNICAL DETAILS:
Adjustment range welding current (TIG) | 10 -200 A |
Adjustment range welding current (MMA/Elektrode) | 10 -170 A |
Setting range welding current (CUT mode) | 20 - 50 A |
Duty cycle (ED) TIG 40°C | 200 A at 18 V 40% |
Duty cycle (ED) MMA/STICK 40°C | 170 A at 26.8 V 25% |
Duty cycle (ED) Plasma cutter 40°C | 50 A at 100 V 40% |
Input Voltage | 1 x 230 Volt |
Power frequency | 50 - 60 Hz |
Protection class | IP23 |
Dimensions in mm (L x W x H) | 380 x 160 x 360 |
Weight (kg) | 11,5 |
Standards | EN60974-1 / EC60974-1 |
Maximum cutting capacity (manually guided) | 13 mm |
Quality cutting capacity (hand guided) | 8 mm |
New York 2500 Scope of delivery:
AC/DC TIG welding machine with plasma cutter New York 2500 |
Automatic welding helmet |
foot pedal remote control |
WIG torch: WP 17 (9 mandrel, 5 pole), 4m with gas quick-acting closure |
1kg TIG welding rods aluminium |
1kg TIG welding rods stainless steel |
1kg TIG welding rods steel |
10x gas nozzles (2x per size 4,5,6,7,8) |
4x clamping sleeve housing (2x per size 1.6 and 2.4) |
4x clamping sleeves (2x per size 1.6 and 2.4) |
2x fire caps (1xlong/1xshort) |
10 pack tungsten electrodes (size 1,6 grey) |
WIG- Set, 14 pieces |
plasma torch: AG-60 (9 mandrel, 5 pole), 4m |
AG-60 plasma wear parts set (25 parts) |
electrode pliers (9 mandrel), 3m |
ground clamp with ground cable (9 mandrel), 3m |
water separator |
gas connection hose |